|
Tube Pullers - Other |
 |
| |
|
RHINO
JR. HYDRAULIC SPEAR TUBE PULLER
CAPTAIN AMERICA PULLER - HTPS
1000
 |
FEATURES
This is really a GREAT Puller and is a fully
self-contained Workhorse Designed & Proven to
provide years of trouble free service.
• Our "Captain America" puller - Fast, Easy, Dependable pulling unit used to pull stubs or entire tubes with 10 tons of "Power"
• 4" of pull in single, quick stroke and can pull up to 180 stubs/minute
• Single person operation and full selfcontained system
• Ideally suited for removing 1/4" to 1" OD tubes of all gauges in up to 4" thick tube sheets
• Unit comes complete with Pulling Gun and Hydraulic pump
• Hydraulic Power Unit operates off of 110VAC
• Spring Balancer for “weightless” support of the Pulling Gun (optional)
|
RHINO JR. PINE JENNY HOLLOW CORE RAM PULLER
|
FEATURES
• One of the most commonly used
style of pullers around, used to
pull stubs or entire tubes with
30 tons of “Power"
• 6" of pull in single stroke,
when used with the “Double
Horseshoe Adaptor" can pull up
to 12" without resetting
• Proven in performance and
usefulness
• Can be used to pull tubes from
1/2" up to 3" of all gauges and
tube sheets up to 8" thick
• Foolproof construction and
simple to operate
|
 |
PINE JENNY STYLE TUBE PULLER SPEARS
|
FEATURES
• Compatible with other manufacturers same style (Pine Jenny, Hollow Core Ram, etc...)
• Manufactured to enhance performance & increase longevity
• Available for 1/2" thru 3" tubes of all Gauges
|
|
RHINO JR. COLLET
PULLER
 
|
FEATURES
Designed for fast removal of all
tube types from Condensers. Heat
Exchangers and Boilers. A rapid
stroke allows the removal of up
to 10 tubes a minute with
minimal operator effort.
Gripping and pulling performed
in single operation. Insert
puller into the tube and
actuate, the jaws will grip the
tube ID and pull out the tube.
• Available in two sizes:
• CTP-900 for 5/8" 17 Gauge thru
11/4" 24 Gauge
• CTP-1100 for 11/2" 10 Gauge
thru 2" 24 Gauge
• Pneumatic or Electric powered
hydraulic pump standard
• Spring Balancer for “weightless"support of the Pulling Gun (optional)
|
|
DRESSER COLLET PULLER
|
FEATURES
• These items will REPLACE & INTERCHANGE with the Airetool/Dresser Pullers
• Sizes available from 5/8" thru 1" Tubes, all Gauges
• Manufactured by USA Industries to enhance performance & increase longevity
Call for Sizes & Availability
|
 |
RHINO JR. MANUAL TUBE PULLER
|
FEATURES
• Used for small, light duty pulling jobs
• Using a wrench screw, screw the spear “A" into the tube then begin pulling by turning nut “B". After tube is free from the tube sheet, remove by unscrewing the spear “A" while holding the tube with channelocks or a pipe wrench.
• Available for 1/4" thru 13/8" tubes of all Gauges.
|
 |
ONE REV INTERNAL TUBE CUTTER & REPLACEMENT BITS
|
FEATURES
One Revolution Internal Tube Cutters are used for the following applications:
1. The “Piercing" of tubes prior to inserting tube plugs
2. The “Complete Cutting" of ferrous or copper tubes on one end prior to tube removal - can include nonferrous light wall tubes
Used with a wrench, simply adjust the depth collar stop so the cutter bit is past the tube sheet, then rotate in a clockwise direction. After the bit starts cutting, make 1/4 revolution to puncture or one full revolution to cut.
• Available for 1/2" thru 21/4" tubes of all Gauges
• Standard reach of 10", longer reaches available
Our Bits are made from high quality tool steel and hardened to provide the maximum cutting edge retention. • Available for 1/2" thru 21/2" tube cutters • Directly interchangeable with Airetool Bits
|
|
PUSH CUTTER INTERNAL TUBE CUTTER AND REPLACEMENTS
|
FEATURES
The Push Type cutter is used to
quickly cut tubes in large
numbers, they are especially
suited for toughest tube cutting
applications such as Stainless
Steel, Inconel, Monel, Titanium,
etc.
The unit can be used with any drill or one of our driving units with the cutting speed regulated for your particular tube material to maximize the cutters life.
To operate, adjust the collar depth, insert it into the tube, apply power, press inward and the tube will be cut in a few seconds.
• Available for 5/8" thru 11/2" tubes of all Gauges • Bits are easily removed
• Adjustable reaches available: “STD" = 4", “A" = 6", “B" = 8", “C" = 10"
Our bits are made from high quality tool steel, hardened, and Titanium Nitrate coated to provide the maximum cutting edge retention,
|
 |
BOILER TUBE CUTTER and REPLACEMENT BITS
|
FEATURES
• PR-68 tube cutters are ideal
for cutting thick walled boiler
tubes of 2" O.D. and higher
• The unit can be operated with
any drill
• For Boiler tube sizes 2" thru
41/2" all Gauges
• Available in standard reach of 4", Additionally reaches in increments of 4" are available up to 16"
|
 |
|
|
| Quick Quote |
|
|
Form Object
|
|
| |
|
Inquire About Product Demos At Your Location
Click Here
|
| Latest News
[All News] |
|
| |
04.16.12 |
 |
Engineering & Maintenance 2012 Trade Show.
USA Industries, Inc. will be hosting Booth #418 & #420 at the ASME Plant
|
| |
Read More
|
|
|
| Downloads |
|
|
|
|
|
|
| |
|
